Home > Arrows > Traditional Arrows > Instinct® Traditional Arrows >

Instinct Traditional Micro-Diameter Shafts
Vintage 100% Carbon Arrows By Black Eagle Arrows

Our Price: $101.99

: Usually Ships in 24 to 48 Hours

Instinct Traditional Shafts:


**** SOLD by the Dozen*****


Our Instinct® arrow is the ONLY wood-grain-micro-diameter-carbon-traditional arrow on the market today. Designed to be more shootable, the Micro-Diameter size helps to offset the off-center design of most recurve and longbow risers made today. We also coupled the Instinct® with our SUPER TOUGH Stainless Steeloutserts, that weigh 100 grains, so you can have the weight up front where you want it.

Each Instinct® Duracoat wood grain overlay-finish on the shaft allows for refletching and cresting. Instinct® arrows are straightness sorted, spine matched, and weight matched—to ensure the quality and toughness that you have come to expect from Black Eagle Arrows. We feel that traditional archers should no longer have to use traditional arrows. Test your Instincts® and experience the Black Eagle difference today!

To install the outsert.

  1. Select the right outsert for the right shaft.
  2. Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
  3. If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits snug on shaft. Start slowly so you don't remove to much off the arrow.
  4. Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
  5. Again, Spin test to ensure concentricity. Rotating outsert until it spins perfect.
  6. Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment once glue is applied.
  7. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
  8. Apply a even amount of glue around the shaft to ensure the glue channels get enough glue in them to hold.
  9. Once The outsert is glued on stand the arrow on the nock end to dry.


Straightness or Straighter
± 1
Grain Weight Tolerance
Shaft Length

Don't forget extra components


Not sure what size is right for you. Check out our sizing chart.

Spine Inner Diameter Outer Diameter GPI
350 .165" .248" 10.6
400 .165" .240" 9.4
500 .165" .236" 8.8
600 .165" .231" 7.9

Hot Melt is NOT recommended for use with Black Eagle Arrow shafts.

Black Eagle High Quality Fletching Adhesive Screw-In Field Point 5/16 Carnivore, Outlaw, Zombie Slayer, Vintage Brass Insert Carnivore, Outlaw, Zombie Slayer, Vintage Screw-In Brass Insert Weight
Our Price: $9.99

Our Price: $9.99

Our Price: $13.99

Our Price: $14.99

Black Eagle Arrows fletching adhesive Screw-In Field Point 5/16 Carnivore, Zombie, Outlaw Brass Inserts Carnivore, Outlaw, Zombie Slayer, Vintage Screw-In Brass Insert Weights
Carnivore, Outlaw, Zombie Slayer, Vintage Break Away Glue-In Target Point 2" Black Eagle Arrows Signature Blazer® Vane Carnivore, Outlaw, Zombie Slayer, Vintage Pin Bushing Carnivore, Outlaw, Zombie Slayer, Vintage Adjustable Weight Target Point
Our Price: $24.99

Our Price: $8.99

Our Price: $14.99

Our Price: $16.99

Black Eagle Arrows Carnivore, Zombie Outlaw Points Black Eagle Arrows Signature Vanes Carnivore, Zombie, Outlaw Pin Bushing by Black Eagle Arrows Carnivore, Zombie, Outlaw Adjustable Target Points
Black Eagle Arrows Standard Nock Black Eagle Arrows "M" Micro-Nock
Our Price: $9.99

Our Price: $9.99

Black Eagle Arrows Standard Nocks M nock for Black Eagle G/M Bushings

Average Rating: 5 of 5 Total Reviews: 1 Write a review »

  0 of 0 people found the following review helpful:
Awesome arrows February 15, 2017
Reviewer: Kevin G from Jacksonville, FL United States  
Just got a dozen shafts the other day and have them fletched up and outserts installed. I really like the 100 grain outserts as they really help boost front of center and get arrow weight up. Woodgrain looks good. Awesome straightness and spine as always.

Was this review helpful to you?