Home > Components > Rampage Components >

Rampage-Renegade Series Stainless Steel Bone Crushing Half-out
Rampage, renegade Stainless stee Bone Crushing Half out


 
Our Price: $21.99

: If Item Can't be ordered it is out of Stock


Quantity*:


Qty:
Description
 
The Rampage-Renegade Stainless Steel Bone Crushing Half-out has been tested and designed by experienced hunters and target archers to ensure maximum penetration and performance. Having been thoroughly tested through many different materials this ensures excellent penetration and shot after shot performance. If you are looking for maximum penetration and shot after shot performance then the deadly combination of the Rampage and Renegade Stainless Steel Bone Crushing Half-out and Shaft are sure to be a hit!
Stainless Steel Half-out - 51 Grains

To install the Half-Out.
  1. Square the end of the arrow shaft
  2. Dry fitting is recommended on all components. Slide half-out in shaft and spin test (if you prefer)
  3. If a slight wobble is noticed, DON'T PANIC! Rotate the half-out with field point installed until the spin is true.
  4. Again, Rotate Half-Out until it spins perfect.
  5. Use a Silver or Black Sharpie and mark the Shaft and the Half-Out for perfect alignment once glue is applied.
  6. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
  7. Apply a even amount of glue around the shaft of the Half-Out to ensure the glue channels get enough glue in them to hold.
  8. Once the glued half-out is finished stand the arrow on the point to dry.
Marked for a perfect Spin Step#5


Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 24 Write a review »

  0 of 0 people found the following review helpful:
 
4 of 5 Love these things. Hard hitting and accurate March 16, 2020
Reviewer: Drew Gann from Demorest, GA United States  
Wish I had gotten them a lot sooner. They hit hard enough that they are blowing through some of my targets. The same target my precious arrows were not blowing through

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Quality March 8, 2020
Reviewer: Thomas Christie from Bristow , VA United States  
So far I’ve been very impressed with the quality and tolerances for the components and arrows vs my other previous brand.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
3 of 5 Wrong order sent February 8, 2020
Reviewer: Colby Burch from Santa Fe , TX United States  
I either ordered the wrong insert by mistake or was sent the wrong inserts. I need to send them back and receive the next size up.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 October 1, 2019
Reviewer: Charles Forbis from Quapaw, OK United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Half Out September 15, 2019
Reviewer: Matthew Bryant from Longview, TX United States  
I'm admittedly a little bit of a nut when it comes to the details..  I researched as much as I could about accurizing and building arrows as I could find, did a bunch of experimentation with fletching, FOC, various arrow weights, spine alignment and nock tuning.  Wound up going with a .300 spine rampage, with a 50 grain screw in brass insert weight, a 50 grain stainless steel half out, 7 inch bohning white wraps, bhoning heat vanes in a 3 flectch left helical configuration.  This setup on my Bowtech SS @ 70#'s with a 29 inch draw length is crazy accurate.  I can't shoot at the same spot on my target or I will split arrows.  I split one tonight all the way to the insert, and center punched the nock onto my field tip so squarely that I had to use a pair of vice grips to remove it from the field tip.

Was this review helpful to you?

View All Customer Reviews