Home > Components >

X-Impact Front Of Center Outsert System F.O.C.O.S (Patented)
X-Impact F.O.C.O.S Outsert system


 
Alternative Views:


Price per Dozen $41.49


: If Item Can't be ordered it is out of Stock


Outsert Metal Choice*:


X-Impact Outserts*:


Qty:
Description
 
      Front Of Center Outsert System (Patent#US10203185)

      QTY IS 1 DOZEN:
      Our New Front Of Center Outsert System is designed for those that want more weight upfront and ease of use of Outserts. The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outsert Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!
      Insertion Depth of Arrow in Outsert is .610 almost 5/8"
      Outsert adds Approximately 1.090" to end of the Arrow
      The Deep Impact & X-Impact Outsert Weights are a Follows:

      ALUMINUM OUTSERTS TOTAL WEIGHT
      ALL SPINES WEIGH 80 Grains

      STAINLESS STEEL OUTSERTS TOTAL WEIGHT
      ALL SPINES WEIGH 100 Grains
        To install the F.O.C.O.S System
        1. Select the right outsert for the right shaft.
        2. Glue in Stainless steel retention Post
        3. Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
        4. If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
        5. You should have approximately 3/4 of an inch insertion on Aluminum Outserts
        6. Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
        7. Again, Spin test to ensure concentricity.
        8. Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
        9. Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
        10. If using glue See steps 11-15 .
        11. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
        12. Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
        13. Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
        14. Use the 3/32 Head retention Screw and Lock the Outsert in place!
        15. Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
FOCOS Outsert Review and Installation

Average Rating: Average Rating: 4.5 of 5 4.5 of 5 Total Reviews: 24 Write a review »

  0 of 0 people found the following review helpful:
 
4 of 5 FOCOS System September 28, 2020
Reviewer: Ryan R Ellison from El Dorado Hills, CA United States  
Easy to install, light sanding required for a few of the impact collars, very satisfied.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 F.O.C.O.S outsert system September 26, 2020
Reviewer: Harry Reed from Midvale, UT United States  
This system is hands down the best I have used. You can align your broadheads if you wish if mess one up rock/tree etc. screw on a new one and be on your way. Very innovative

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Very good outserts and online experience September 25, 2020
Reviewer: Jeff Finn from Englewood, CO United States  
Have been using these outserts for about a year.  Shopping experience is good/quick and delivery was very fast.  Thanks

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Tip weight August 30, 2020
Reviewer: Ullysses Suarez from Mount Arlington, NJ United States  
Great system! I highly recommend it

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 FOCUS INSERT/OUTSERT May 27, 2020
Reviewer: Andrew Brakke from Monroe, WA United States  
Recently built a set of Black Eagle X Impact 250 Spine with 80G FOCUS SYSTEM. Awesome product! Durable, Spins True, Amazing FOC. Throwing 100G QAD Exodus Head on them....Hits like a Hammer. Excited for elk season here in WA.

Was this review helpful to you?

View All Customer Reviews