Black Eagle X-Impact Outserts
SKU: Ximp_BLK-OUTSRT
Black Eagle Arrows

Black Eagle X-Impact Outserts

$25.99
Quantity per pack 12
These black anodized 7075 T6 aluminum alloy outserts have been tested and designed by experienced hunters and target archers to ensure maximum penetration and performance. This outsert fully encompasses the base of the shaft just over 1 inch providing OUTSTANDING arrow strength and concentricity. With Micro-Glue channels inside the outsert to create a much better bonding surface this outsert is built to last shot after shot. If you are looking for maximum penetration and shot after shot performance then the deadly combination of the Deep Impact or X-Impact shafts and this outsert are sure to be a hit!
 
The Deep Impact & X-Impact Outsert Weights are a Follows:
  • 250 Spine = 42 Grains
    300 Spine = 40 Grains
    350 Spine = 44 Grains
    400 Spine = 46 Grains
    500 Spine = 48 Grains

To install the outsert.

  1. Select the right outsert for the right shaft.
  2. Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
  3. If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits snug on shaft. Start slowly so you don't remove to much off the arrow.
  4. Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
  5. Again, Spin test to ensure concentricity. Rotating outsert until it spins perfect.
  6. Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment once glue is applied.
  7. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
  8. Apply a even amount of glue around the shaft to ensure the glue channels get enough glue in them to hold.
  9. Once The outsert is glued on stand the arrow on the nock end to dry.
Full Description
Qty
  • Description
    Quantity per pack 12
    These black anodized 7075 T6 aluminum alloy outserts have been tested and designed by experienced hunters and target archers to ensure maximum penetration and performance. This outsert fully encompasses the base of the shaft just over 1 inch providing OUTSTANDING arrow strength and concentricity. With Micro-Glue channels inside the outsert to create a much better bonding surface this outsert is built to last shot after shot. If you are looking for maximum penetration and shot after shot performance then the deadly combination of the Deep Impact or X-Impact shafts and this outsert are sure to be a hit!
     
    The Deep Impact & X-Impact Outsert Weights are a Follows:
    • 250 Spine = 42 Grains
      300 Spine = 40 Grains
      350 Spine = 44 Grains
      400 Spine = 46 Grains
      500 Spine = 48 Grains

    To install the outsert.

    1. Select the right outsert for the right shaft.
    2. Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
    3. If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits snug on shaft. Start slowly so you don't remove to much off the arrow.
    4. Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
    5. Again, Spin test to ensure concentricity. Rotating outsert until it spins perfect.
    6. Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment once glue is applied.
    7. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
    8. Apply a even amount of glue around the shaft to ensure the glue channels get enough glue in them to hold.
    9. Once The outsert is glued on stand the arrow on the nock end to dry.
  • Reviews

    Reviews

    Dale T

    x impact outserts

    These are great. Not only do they balance very well concerning weight, but they have also saved two arrow shafts already this year. In the past, the regular inserts have caused the carbon shafts to splinter upon hitting a tree on a pass-through, but these keep them intact where you can dig them out of the tree and the shaft is in perfect condition.
    JD Sias

    Arrow Outserts

    Work great. Perfect for my 2022 Elk arrow build.
    John

    Nice outsert

    Guys you have to follow directions or you will complain about these. All the guys at bow shop don’t like these because they say the inserts come off. You must use black eagles glue. It’s in the directions. If you use there glue, inserts work perfect. No problems. Buying more to make more arrows…
    Tim Forsythe

    My only complaint is that I am not able to find ou

    My only complaint is that I am not able to find out when the arrows will be delivered. I’ve reached out to the post office with the order number but cannot get a response
    Bryce Olson

    Outserts X-Impact

    Love the design of these outserts. They fit nicely to the shaft, protect the shaft from breaking when striking a hard surface, and match up my 5/16" points on this microshaft beautifully.
    Nic DiFilippo

    Great Product

    I got my product in the mail in less time then expected. Couldn't be happier to put the Outsert to work. Great Product
    clarence mann

    Ximpact outserts

    These are high quality outserts and the help the penetration on the arrows best i have shot by far !
    Roy Torres

    GOOD

    FINE U HAVE TO REALLY DO GOOD PREP JOB OR INSERT COMES LOOSE IF SHOT IN A FIRM TARGET
    Adam Johnson

    Really good outsert.

    Great product for the smaller shafts they are really tough.
    Michael Stonebraker

    X-impacts

    So after hearing so many good things about your guy’s products, I decided to take the dive and buy your guy’s x-impacts. Today I was able to take them to my local shop and have them cut to length and shoot them for the first time. You guys have went up and beyond my expectations after all the good things I have heard. Money well spent. I support what you guys stand behind and I can promise you have a life time customer. Keep doing what you’re doing. -cheers
    Michael Middleton

    Customer review

    Review body is empty
    DENA GRARD

    Great Component

    Great Company and Great Product
    Dereck Owen

    4

    Wish you had a heavier outsert. 80-100 grain.
  • Details

    Details

    Current Stock:
    SKU: Ximp_BLK-OUTSRT
    Availability: If Item Can't be ordered it is out of Stock